System of EDGE numerical control applies in machine of blaze, Plasma Cutting

The hand moves means to move key to use means window into proceed with by one helper, at this moment mouse arrowhead turns little hand into appearance, use arrowhead bolts, can move in 8 direction random cut machine. The set in if be in,setting bill of fare the lock that the hand moves key is cut surely can, want to press machine of directional key cut to be able to move continuously only, until move key by the hand again till. The bottom that uses means window in the hand has a few button, press these button, can fulfil corresponding function. (1) return start to want to use window into proceed with only, the coordinate dot of two axes of X, Y is saved to come down, after the hand that finish moves an operation, if hope to return this, by " return start " pushbutton, cut machine can return start. (2) mobile distance and cut distance are used " modification hand changes way " pushbutton will choose a hand to move cut and only mobile two kinds of hands change way. Only mobile state cut machine does not implement real cut; The hand is moved cut represents mobile cut opportunity and true tangent is cut, by " mobile distance " or " cut is apart from " pushbutton, controller hints the shift that inputs X axis, Y axis is apart from, press carriage return key, begin campaign. (3) modification shift speed presses this button, one kind chooses in speed of the oldest machine, high rate, middling speed and low speed. 2.

Before automatic cut means is implementing cut, want to set value of cut means, kerf and cut rate above all. Cut means has 3 kinds of choices: Demonstrate means, oxygen to light air means, plasma way. When demonstrating pattern, press START key will make cut machine dogs by process designing speed cut method, but cut was not activationed, when oxygen lights air means and plasma way, press START bolts cut is activationed, when oxygen lights air means, the bottom that show a window appears " increase " , " set " , " cancel " 3 key-press. Show window right bottom to show beforehand the time delay time of buy, by " increase " key will extend warm-up time, until by " set " key or " release " till key. By " set " key can save new warm-up time, by " release " key does not hold new set cost. No matter oxygen lights air means or plasma way, the bottom that show a window shows " raise rate " , " reduce rate " " observation pursues completely " key-press: Press " observation pursues completely " key, controller indicates the central position of cut at any time, by " raise rate " or " reduce rate " cut machine raises rate or decrease 3% . Want to change current cut speed to be able to press carriage return key, make current rate shows new rate of brightness, input is worth, press carriage return bolts controller accepts input rate again. 3.

Suspensive kind fails in the cut below inevitable circumstance, want to bolt by STOP at this moment, make cut machine is in suspensive condition, controller has the capacity that restores cut in the round. Appear in the bottom that shows a window " return start " , " time retreat " , " ongoing " , " go bit more perforative " key-press. By " return start " hind, cut machine will return the initiative cut part of plank; By " time retreat " or " ongoing " key-press, cut aircraft will move after the floating rate by the choice or reach arrives any positions of cut workpiece, will press process designing speed by machine of START key cut again new cut. By " go bit more perforative " key, controller allows handlers to move directly cutting torch is nodded to stiletto. After the input makes the news that wear a dot, by " carriage return bolts " cut equipment moves directly to you the perforation of set is in. In suspending window, can use all functions of key with the hand, allow a machine to move along any direction, once method of original cut of cut equipment deviate, show different window, show window bottom appears at this moment " return way " " mobile workpiece " key-press. Press " return way " key, cut machine will nod those who return former way on, this function is right when examination or the part that replace facility very useful. Press " mobile workpiece " after key-press, the position that changes workpiece to go up in plank, the position with current located cutting torch can be treated as to suspend the work place when cut, receive next START key at this moment, cut machine begins the cut of odd workpiece locally here. 4.

Work options presses " work options " key, allow handlers to undertake to the workpiece in current memory a series of custom-built operation, show window bottom to appear at this moment " kerf " , " repeat " , " corrective " key-press. Show appear on the right side of the window " scale factor " , " corner coming back is spent " , " X axis and Y axis mirror " parameter inputs an area, input corresponding parameter, can realize these functions. Press " kerf " key, monitor is shown with green piece cut the way that seams a course, this can observe before cut whether kerf is correct. Press " repeat " key-press, show parameter appears to input an area on the right side of the window, handlers inputs these parameter by need, the array that can realize workpiece is arranged. 3 kinds range way: Discharge the type, crisscross type, type that cover a platoon continuously, this function can realize simple platoon stuff, with realizing workpiece for many times cut. Press " corrective " key-press, appear corrective show a window, the window is shown in this under, can come true tilt be opposite on plank neat workpiece. Particular operation is as follows, press " editor parameter " key, set parameter. These parameter include: Rotate reference point, the top left corner that has board, left next horn, top right corner, right next horn choose 4 kinds; Open bend slop regulation to make switch, tilt reference point, those who have board stuff is left next horn, top right corner chooses two kinds, after parameter has been chosen, move cutting torch to the horn of the first fixed position, press " calm corner " key, press " tilt surely dot " hand of edge of key edge plank moves shift to arrive inclined pour point, press again " calm corner " , press again " affirm " key, cutting torch returns workpiece start, workpiece happening rotates to already was opposite with armor plate neat, show advocate stroke engine can begin cut. 5.

Controller of graphical library EDGE has function of graph dish library, graphical library includes 50 kinds of commonly used work. Be in advocate below indication window, press " graphical library " key, graph of 50 kinds of workpiece shows in monitor, use, below, key of left, right arrowhead will choose. After by carriage return key chooses work, the workpiece of make choice of appears in indication window, those who show a window on the right side of occurrence parameter area. Handlers can input parameter, the length that these parameter include work, height, radius, introduce, derivative line and the kind that make secant, by " affirm " after key, workpiece graph is chosen advocate picture. 6.

Graphical management implement the graphical management of EDGE implement have text editor, figure oriented, cover the function such as makings. Manage in the graph implement show a window to fall, by " text edits " the program code that key can be inputted or edits ESSI or EIA format, enter this window, show the current work program in memory. If want to edit new work, press first " delete " key-press deletes current work program, press " the graph is oriented " key-press, can edit work program with graphical means, EIA code can insert work program directly or found part drawing. By " the hand moves an editor " key, allow to edit the window to have an edition to Gao Liang's travel in text, replace text to edit the text in the window with the part that selects from inside component type window, before also can inserting the component of the choice what text goes or later, while these are operated, workpiece graph shows change at any time. EDGE system still has the function of a makings, allow handlers to be opposite classify of a group of workpiece, set makings, use board with utmost. Particular operation is manage in the graph implement the window is pressed " set makings " key enters a makings order, handlers is OK the input of the key-press of window and parameter will add the distance between the workpiece, cut order that deletes workpiece, certain work, certain work to wait. When adding workpiece, allow an user to choose from graphical library, disk, lead plane, after make choice of ends, workpiece will show on plank preparation determines the position, if be in parameter set function of automatic fixed position, controller will search a position automatically to set work, handlers can undertake adjustment to workpiece, shrink for instance put, mobile, rotate, mirror, press finally " affirm " key, return advocate window, begin cut. 7.

The setting enters setting menu, the parameter that handlers can need to cut machine place has set. (1) these parameter include cut parameter the speed of mode of the dimension of plank, cut, cut, cut those who crack code of program of value, RS-2740D absolutely or code of F of increment means, speed is effective, halt time. (2) the cut that controller of cut type parameter contains a few kinds of levels handles logic it, allow cut process to configure sequential, in order to obtain optimum behavior. To oxygen means burning gas and sequential of plasma means cut are different. ① lights air means in oxygen when, handlers can ignite according to needing actually to be opposite time, warm-up time, perforative time, creeping time, cutting torch rises, decay time, when is cut gas shut, and the parameter setting such as the time that arranges gas. After these parameter are installed, by blank space key can watch sequential chart form, if satisfaction is pressed,affirm key to save parameter. ② falls in plasma means, handlers can fight each other the time of aperture, creeping time, cut shuts time, rise, decay time, and the parameter setting such as stopping time; Also can be opposite signal of feedback of the electric current removing arc, electric current that corner is in, arc undertakes installing. (3) the note if the plasma power source that you use has arc feedback signal, arc feedback signal must be opened when Plasma Cutting means, removing arc to become after cutting, the car begins after system of EDGE numerical control receives the arc feedback signal that comes from plasma. 8.

The file is right simple work program, handlers can use editor function or oriented function is in the graph the process designing on EDGE system or call from inside graphical library directly, but expect to needing to cover commonly for big board, cover expecting is to going up finish on machine. EDGE system provided file function, can realize workpiece conveniently going up between a machine and EDGE system deliver. In advocate press below the picture " file " pushbutton, enter file function window, this window place draw together 4 key-press: "Lade from disk " , " stock disk " , " lade from the computer " , " lade the computer " . EDGE has floppy disk and hard disk drive, the user allows to found many his folder on hard disk, found folder to use " + " key, delete folder to use " - " . Referenced area appears on the right side of the window after the operation chose disk to deliver, allow to handlers is inputted or choose a few parameter. For example: Hold a file from where, lade where goes, can choose the corresponding folder of graphical library, memory, floppy disk, hard disk. Whole in window paradigm gives the document that should deliver, the user can choose a file or a group of files, but lade can hold file of a workpiece only in memory. The file in installing hard disk folder but one with having name of a file additionally. After choice lead plane transfers a function, show a window on the right side of area of meeting occurrence reference, these reference include: Lade from where, lade where, the user can choose to download a file from the which catalog of lead plane, download a certain folder of the memory of EDGE or hard disk; A certain folder of the memory from inside EDGE system or hard disk chooses a file to deliver lead plane, in the which folder that delivers lead plane. The file in the corresponding folder in the in corresponding folder all file in lead plane or EDGE hard disk can show in showing a window, offer handlers alternative. The file that handlers can give download or the file that upload lead plane have a name additionally. Pass file function, handlers is OK very prepare workpiece document for EDGE system conveniently or save has used work rise. Anyhow, system of EDGE numerical control is in the function of respect of numerical control blaze, Plasma Cutting is very perfect, the article is this to do a few simple discussing, in order to offer the design personnel of cut machine or handlers reference. CNC Milling CNC Machining